Jetty layout logic in a configurator: berths, finger booms, pier spacing and site checks
Parameters and rules of a floating jetty configurator: pier type, sections, finger booms, berth count, pier spacing, site checks and the brief.
Short answer: a jetty configurator counts in berths, not metres. Its logic links three levels: the piers (type, width, sections, position on the shore), the finger booms (type, length, spacing, sides) that produce the berth count, and the site (depth, pier spacing, exposure, ice) that produces notes for the site visit. What comes out is a brief, never a design.
What are the inputs?
Unlike a single dock, the buyer does not pick a product with options here, but lays out a facility. The inputs fall into four groups:
| Group | Parameters | Depends on |
|---|---|---|
| Pier | Type, width, sections and their lengths, position along the shore | the type sets the widths and section lengths on offer |
| Booms | Type, length, width, sides used, fitting | boat size; pier type and fitting |
| Equipment | Gangway, breakwater, anchoring, bollards | shore height, exposure, pier type |
| Site | Shoreline length, water depth, exposure, ice, boat beam | entered by the buyer or assumed |
The first rule is also the most important: the pier type decides what can be chosen next. Each pier type, such as a light pier, a heavy pontoon or a wide quay for work boats, has its own widths, section lengths and equipment. When the type changes, width and sections must be brought back to valid values, with a visible message rather than a silent correction.
How is the berth count worked out?
For a harbour operator, the berth count is how a layout is judged. It follows from a few quantities:
- Boom centre spacing = boat beam + boom width + an allowance that your company sets.
- Berths per side = usable pier length ÷ centre spacing, rounded down.
- Sides used: none, one or both.
A simplified calculation with freely chosen numbers: with a 3.0 m boat beam, a 0.3 m boom and a 0.5 m allowance, the centre spacing is 3.8 m. A 40 m pier then gives 40 ÷ 3.8 = 10.5, so 10 berths per side, or 20 with both sides used. Pier heads, the gangway connection and gaps for access are left out here; in a real configurator they are rules too.
Boom length follows boat length, and the boom type (plain, with a mesh section, walkable) decides which lengths and widths exist. The fitting that holds the boom to the pier may decide whether spacing can be changed later. All of this is your product data, read from your tables. Our example configurator shows Y-booms with berth spacing and berth count [1]; the count is an estimate with example values.
Which rules apply between piers?
Once a layout has more than one pier, a second kind of rule appears: the distance between piers. Between two piers with booms, the booms on both sides and a fairway for manoeuvring must fit. If the piers are too close, booms overlap and the berth count would be wrong.
A configurator should handle this in two steps: flag a tight distance as a note, and stop counting berths when booms would overlap. Which fairway width you allow for is your rule. In the demo, pier spacing is one of the site checks, and piers slide along the shore with a drag handle [1]. The buyer sees the effect of a distance without typing a number.
How are site conditions handled?
Site inputs are not inputs to a calculation; they trigger notes. Four are typical for jetties:
- Water depth: if it looks shallow for floats, anchoring or a breakwater, a note asks for a check on site.
- Exposure: sheltered, moderate or exposed. A light pier type on an exposed site without wave protection should trigger a note.
- Ice: if the facility stays in the water all year, ice and drift ice go on the list of open questions.
- Pier spacing: see above.
Wording matters. A note says "check on site", never "suitable" or "safe". Values the buyer did not enter should appear as assumptions in the summary. In the demo, site checks and sizes are simplified sample values, explicitly not a structural design, not a permit check and not a quote [1]. For your real product, design, anchoring and permits are the responsibility of your company, with consulting engineers and the relevant authority where required. The configurator only collects the questions.
What goes into the site-visit brief?
The output of a jetty configurator prepares the visit. Useful rows are:
- per pier: type, width, sections with lengths, total length, booms and estimated berths;
- booms: type, length, spacing, fitting;
- gangway, breakwater, anchoring, bollards;
- site details, each marked "entered" or "assumed";
- the notes that were triggered;
- a fixed list of what is decided on site in any case.
In the demo this brief can be copied and downloaded as a PDF [1]. In your project it goes to your team by e-mail or webhook, with fields for the harbour name, the municipality and a preferred visit period if you want them. Who receives it and how it is followed up is covered in dock configurator enquiries, site visits and dealers.
Try the example
The floating jetty configurator is an example configurator by Modelwright with a fictional product and example values. Start with the "small-boat harbour" preset, slide a pier and watch berths and notes change. Boats, anchoring and dimensions can be shown or hidden.
Example configurator · fictional product
Floating jetty configurator
Plan a floating jetty: presets for a guest jetty or small harbour, slide the piers, booms and berths, breakwater and fittings – with site checks and a PDF enquiry.
Who such a configurator is for is covered in marina and jetty configurator software, and the technical build in implementing a dock configurator. For a project of your own, see custom 3D configurator development.
Frequently asked questions
Is the berth count binding?
No. It is an estimate from the inputs. Your team sets the final layout after the site visit.
Can one layout mix pier types?
Yes. In the demo, type and width are chosen per pier. In your project, the combination rules of your range apply.
Can we define our own site notes?
Yes. The condition and the text of each note come from you, for example from which depth or exposure a check is recommended.
Sources
- Modelwright library, floating jetty configurator, "Live in this demo" list and sample-value note, read 14 November 2026: modelwright.de/en/library/floating-jetty-configurator/


