Yard ramp slope, bed height and checks as configurator rules
How a yard ramp configurator calculates slope from length, level-off and bed height, and checks lift range, door opening and forklift clearance.
Short answer: a yard ramp configurator needs one calculation and four checks. The calculation gives the slope from overall length, level-off and bed height. The checks ask: is the bed height within the lift range? Does the lip fit the door opening? Is there room beside the forklift? Is the flat level-off longer than the forklift's wheelbase? Our example configurator calculates and checks all of this live with example values.
Which parameters does a yard ramp have?
In the example configurator six steps lead through the configuration: product, dimensions, options, finish, review and enquiry. The inputs that drive the calculation and checks:
| Parameter | Values in the example | Affects |
|---|---|---|
| Ramp type | Mobile, static, container ramp | Length and width range, lift range, wheels |
| Vehicle | Truck/trailer or container on chassis | Door opening, suggested bed height |
| Overall length | 9 to 15 m (container ramp up to 12 m) | Slope |
| Level-off | Flat section at the truck end | Slope, check against forklift wheelbase |
| Usable width | Between the curbs, 2.0 to 2.5 m by type | Lip width, side clearance |
| Bed height | Height of the truck bed | Slope, lift range |
| Slope limit | Set by the user, default 12 % | Green or red |
All values are example values for a fictional product, not ratings [1].
How is the slope calculated?
The ramp has an incline and a flat level-off at the truck end. The incline is therefore overall length minus level-off. It spans the bed height, so the horizontal run follows from Pythagoras and the slope is height divided by run:
- Incline = overall length − level-off
- Horizontal run = √(incline² − bed height²)
- Slope in % = bed height ÷ horizontal run × 100
Worked through with the default values: 13.5 m overall length, 2.5 m level-off, 1.30 m bed height. The incline is 11.0 m, the run √(121 − 1.69) ≈ 10.92 m and the slope 1.30 ÷ 10.92 ≈ 11.9 %, just under the 12 % example limit. Raise the bed height to 1.45 m and it becomes 13.3 % and turns red. With a 15 m ramp, the slope at the same bed height drops to about 11.7 %. The configurator names this way out itself: a longer ramp or a shorter level-off lowers the slope.
What we checked: the readout in the panel, the label in the 3D model and the enquiry text show the same figure. We recalculated eight configurations across all three ramp types by hand; all matched.
Why can the slope limit be adjusted?
The slope a forklift can climb is set by the forklift maker's data; the ramp alone does not decide it. So in the example the limit is a value the user sets between 5 and 25 %; the 12 % default is an example value. The message in the configurator says explicitly that the forklift maker's data is what counts. In your configurator you can fix the limit, let users pick it by forklift class or leave it open as in the example.
Which checks run alongside?
| Check | Rule in the example | Result |
|---|---|---|
| Lift range | Bed height within the type's lift range, 1.00 to 1.70 m for the mobile ramp | Red: lip rests at an angle or cannot reach |
| Lip and door opening | Lip width (usable width − 120 mm) at most door opening − 60 mm; door 2.48 m for a truck, 2.34 m for a container | Warning suggesting a narrower usable width |
| Side clearance | (Usable width − 1.15 m forklift width) ÷ 2 at least 300 mm | Warning |
| Level-off | Longer than the example forklift's 1.6 m wheelbase | Warning: a longer level-off is calmer |
If the bed height is above the lift range, the ramp in the model rises to its limit, the lip hangs and the readout shows "outside lift range". The checks do not block the enquiry; their results appear in review, enquiry text and PDF. All limits are example rules and replace neither a check by the maker nor a risk assessment.
Which options change what?
- Height adjustment: hand pump or electro-hydraulic on mobile and container ramps, fixed legs on the static ramp. The static ramp has no wheels and no tow coupling.
- Capacity class: 6 to 12 t as example classes. They change the stringers and cross-members in the model and nothing else; they are not a capacity rating.
- Deck and finish: open or serrated grating, checker plate; hot-dip galvanised or painted in RAL colours.
- Accessories: lip, handrails, curb, wheels, tow eye or tow bar, support legs.
In testing, every option visibly changed the model; 42 changes were counted.
What comes out at the end
The review shows every value and check. The enquiry text has the same rows, and the two-page PDF adds a 3/4 view, a side view with the slope, the checks and a table [1]. In the demo, text and PDF are created in the browser; routing to a maker is not built in. Because the vehicle is part of the configuration, the enquiry contains both bed height and vehicle type, so a dealer can derive an offer for another vehicle from the same enquiry.
What data you supply
For a configurator with your ramps we need: length, width and lift ranges per type, level-off lengths, lip sizes, your capacity data, the vehicle types you cover, your slope-limit rule and the wording your sales team uses for questions. Other industries and uses are covered in our guide to 3D configurators for manufacturers.
Try it
Example configurator · fictional product
Mobile yard ramp configurator
Plan a mobile yard ramp: change the bed height and see the slope at once, checked against an adjustable example limit – with options, review checks and a PDF enquiry.
Test the calculation in the yard ramp configurator, an example configurator with a fictional product and example values. Who benefits is covered in yard ramp configurator for manufacturers; fixed loading bays are covered in dock leveller gradient and working range rules. The project is described on 3D configurator development.
Frequently asked questions
Is the calculation generally valid?
The geometry is; the limits are not. Lift ranges, limits and classes are example values; in a project yours apply.
Are feet and inches available?
The demo is metric only. A unit switch can be added in a project.
Does a red check block the enquiry?
No. The result goes into the enquiry, so your sales team sees what needs discussing.
Sources
- Modelwright library: mobile yard ramp configurator, "Live in this demo" list and example-value note, read 14 November 2026: modelwright.de/en/library/yard-ramp-configurator/


