Kit lists in a configurator: post-and-beam barns, size tables, doors and lean-tos
How a barn kit configurator derives a kit list from building type and size, and which rules doors, windows, lean-tos and cupolas need.
Short answer: a configurator for barn and carriage house kits needs two kinds of rules: design rules, which set the sizes, doors, windows, lean-tos and cupolas that suit each building type, and quantity rules, which derive a kit list from building type and size. The quantity rules count parts according to your grids and sections. They do not replace engineering; they reproduce what you have released for a size.
What does the buyer choose?
| Input | In the example | Proposed dependency |
|---|---|---|
| Building type | Five example barns, saltbox and two-storey | Sets widths, roof pitch, storeys, possible windows |
| Width, length | From size tables | Widths per type; length in fixed steps |
| Lean-to | Optional | Own widths per type; length as the main building |
| Doors | Door type and count, transom | Count limited by length; transom per door type |
| Windows, flower boxes | Upper and extra windows | Upper windows only where the gable has room |
| Cupola | Cupola types and weathervane | Size suited to roof length |
| Colours | Finish and roof | Look only |
| Kit list | With assumed values | Follows from everything above |
This is an example configurator with a fictional product; all values are example values. The first two columns follow the "Live in this demo" list on the library page. The dependency column is our proposal for a manufacturer's configurator, not a description of the demo's logic.
How do size tables become rules?
A post-and-beam building type usually has a few widths and a length that grows in fixed steps, for example in bays between two bents. We propose keeping, for each building type, a list of widths and the length step with minimum and maximum length. The configurator offers only these values. If the buyer switches type and the chosen width does not exist there, it moves to the nearest one with a note.
The lean-to gets its own, smaller list of widths per type. Its length follows the main building if that is how you build it; otherwise it is a separate value with its own limit.
Which rules do doors, windows and cupolas need?
- Door count by length. Each door needs a bay. The maximum number of doors therefore follows from the length; when the building gets shorter it drops, and the configurator says which door goes.
- Transom only with suitable doors. A transom above the door needs height under the eaves, so it is offered only for door types that have it.
- Upper windows only with gable space. Flatter roofs lack the room; the option appears only for building types that have it.
- A cupola that suits the roof. A large cupola on a short building looks wrong. A rule can tie the cupola size to the ridge length or suggest one.
These are rules we propose for a manufacturer's configurator. According to the library page, the demo shows door type and count, transom, flower boxes, upper and extra windows, cupola types and weathervane.
How is the kit list built?
According to the library page, the demo produces a kit list with assumed values and shows the post-and-beam frame when the boards are peeled away. For a real kit we propose counting the list from a few rules you release:
- Posts per bent and side, with the number of bents from length and bay width.
- Rafters at the rafter spacing along the length, on both roof slopes.
- Girts and purlins per bay and wall.
- Sections from a table per building type and width, not calculated.
A worked example with freely chosen numbers, not taken from the demo: a building is 10.8 m long with 3.6 m bays. That gives 10.8 ÷ 3.6 = 3 bays and 4 bents, so with two posts per bent, 8 posts. At 0.6 m rafter spacing there are 10.8 ÷ 0.6 = 18 spaces and so 19 rafters per slope, 38 in total. In this example, adding a door changes the girts in that bay; whether extra door posts are needed is for you to set.
The limit matters: the list counts parts according to your released sections. It sizes nothing. Whether a section is adequate for a span, a snow load or a site is for you as the manufacturer to decide with your own calculations. The configurator should say so beneath the list.
Why show the frame in the model?
For a kit, the view without boards is more than an effect. It shows the same parts that are in the list. We recommend generating model and list from the same data: when a shorter building loses a bent, it disappears from the model and the list at once. The picture then cannot contradict the list, and a self-builder can count in the model what they are ordering.
What data do you supply?
Your building types with widths, length step and limits, lean-to widths, door and window types with their conditions, cupola sizes, sections per building type and width, and a cut list for one example size against which we test the quantity rules.
What comes out at the end
The enquiry should state building type, width, length, lean-to, doors, windows, cupola, colours and the kit list, clearly marked as a list according to your rules. In the demo the enquiry text can be copied and downloaded as a PDF; in a project it goes to your sales team by email or webhook.
Example configurator · fictional product
Carriage house and barn configurator
Put together a carriage house or barn: five example buildings, lean-to, sizes from tables, doors, windows, cupola and colours – with a look at the post-and-beam frame, a kit list and a PDF enquiry.
Try it in the carriage house and barn configurator. Who such a configurator is for is covered in barn kit configurator software. How peeling the boards and phone display are implemented is covered in implementing garden building and sauna configurators. For hiring us, see custom 3D configurator development.
Frequently asked questions
Can the kit list be exported as a file?
The library page lists the kit list as well as enquiry text and a PDF. A file for your costing, such as a spreadsheet, is possible in a project.
Are the demo's quantities reliable?
No. The demo uses assumed values for a fictional product. In your project your grids and sections apply.
Sources
- Modelwright library: carriage house and barn configurator, "Live in this demo" list, read 14 November 2026: /en/library/carriage-barn-configurator/


