Technology

Dock kit logic in a configurator: parts list, access ramp angle and water level

How a dock kit configurator derives a parts list from shape and lengths and shows the access ramp angle as the water level changes.

Short answer: a dock kit configurator counts parts. Shape, main dock length and head length decide how many floats, rails or frames, holders and connectors go into the kit. The access ramp is the second calculation: it is hinged at the shore and rests on the dock, so its angle depends on ramp length and on how much the water level changes. The result is a parts list your warehouse can pack.

Floating dock kit configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

Which inputs does a kit need?

InputValues (example)Affects
Shapestraight, L (head to one side), T (head to both sides)whether there is a head, junction parts
Main dock lengthwhole metres within your limitsfloats, rails, decking
Head lengthwhole metres, L and T onlythe same for the head
Access ramplength, e.g. 1, 2 or 3 mangle, extra parts
Swim islandyes or noits own module with its own parts list
Anchoringanchor-stone holders in a chosen number, or none (provided on site)holders in the parts list
Deckingtimber deck with a finish, or no deckboards and edge trim in the parts list

The number of inputs is small. That is an advantage with kits: kit buyers are not necessarily specialists, and every further question is one they have to answer themselves. Whatever they cannot know, such as the number of floats, the configurator works out.

In the floating dock kit configurator, shape and main and head dock length are chosen in whole metres, together with a hinged access ramp of 1–3 m, a swim island option, anchor-stone holders, and a larch deck or no deck [1].

How does a shape become a parts list?

The parts list comes from quantity rules your system defines. Typical rules for floating dock kits:

  • Rails or frames in stock lengths. If rails or frames come in a few fixed lengths, the configurator has to build every dock length from them, for example 8 m from 3 + 3 + 2 m. Which combination is preferred (fewer joints or fewer stock items) is your rule.
  • Floats per length. The count follows from dock length and your spacing. The configurator does not calculate the capacity behind it; it applies your rule.
  • Connectors and holders at joints and corners. Every joint and every junction between head and main dock adds parts.
  • Decking by area or length. Prefabricated deck panels by length, edge trim by perimeter.
  • Modules as blocks. A swim island brings its own fixed parts list.

A parts list from a configurator is an indicative quantity. It should be labelled that way, with lines based on assumptions marked as such. In the demo, the parts list is shown with sample quantities [1].

How does the ramp behave as the water level changes?

A floating dock rises and falls with the water; the shore does not. The hinged ramp between them pivots at the shore and rests on the dock, so its angle changes with the water level. The geometry is simple: the ramp angle is the arcsine of the height change divided by the ramp length.

Ramp lengthWater level ±20 cm±30 cm±50 cm
1 m11.5°17.5°30.0°
2 m5.7°8.6°14.5°
3 m3.8°5.7°9.6°

These are our own worked figures, not values from the demo, assuming the ramp lies level at the mean water level. They show the relationship, not which angle is acceptable or comfortable. That is for you as the maker to set, with any requirements that apply at the place of use in mind.

This is where 3D does more than a table. The buyer sets the ramp length and sees the tilt per water level on the model. The demo shows a hinged access ramp of 1–3 m with a water-level tilt check; quantities and the tilt check are simplified sample values, not a structural design and not a quote [1].

Two rules are worth adding in a project. A longer ramp may need extra parts, which should then appear in the parts list automatically. And when an angle exceeds your recommendation, the configurator should suggest a longer ramp rather than only warn.

Decking, finish and "no deck"

With timber decking the finish is a real buying decision. Untreated timber changes colour over time, and buyers want to know how their dock will look after a few years. The demo shows a larch deck fresh, glazed and weathered [1]. If the buyer picks "no deck", the parts list must say so clearly: substructure only, decking by others.

What goes into the enquiry or order?

A complete output carries shape, lengths, ramp, modules, anchoring, decking and the parts list with quantities. A field for the water depth at the end of the dock and the type of shore helps your team if a query is needed. In the demo, an enquiry text and a PDF can be produced [1]. In a project the same parts list can be handed to a shop cart; that is covered in dock kit configurator for manufacturers.

Because the buyer assembles the kit, linking the parts list to the 3D model is worth considering: a click on a line shows where the part goes. That is not in the demo, but it is a natural extension; see exploded and function views.

Try the example

The floating dock kit configurator is an example configurator by Modelwright with a fictional product and example values. Choose the L shape, lengthen the main dock, change the ramp length and compare the parts list and the tilt.

Example configurator · fictional product

Floating dock kit configurator

Put together a floating dock kit: straight, L or T shape, lengths, access ramp with a tilt check, swim island and timber deck – with a parts list and a PDF enquiry.

Docks & marine · Dimensions and sizes · Materials and finishes · Options, modules and accessories

How the other dock configurators handle the same questions, and how enquiries move on, is covered in dock configurator enquiries, site visits and dealers. For a project of your own, see custom 3D configurator development.

Frequently asked questions

Is the parts list binding?

No, it is an indicative quantity from your rules. Whether you check it before shipping is up to you.

Can the parts list carry your part numbers?

Yes. In a project we use your part numbers and names so that warehouse and shop speak the same language.

How does the buyer know the water level change?

Not always precisely. That is why showing several values side by side helps more than asking for one exact number.

Sources

  1. Modelwright library, floating dock kit configurator, "Live in this demo" list and sample-value note, read 14 November 2026: modelwright.de/en/library/dock-kit-configurator/

Read next