Horsebox configurator rules: stall layout, ramp angle and payload
The rules a horse trailer and horsebox configurator needs: vehicle type, stall layout, ramps, ramp angle arithmetic, example payload and the enquiry.
Short answer: a horse trailer and horsebox configurator needs three kinds of rules. Validity: which number of horses, stall layout, ramp and living area belong to which vehicle type? Dependencies: one layout requires a particular ramp, and a horsebox needs at least one loading ramp. Calculations: the ramp angle from loading height and ramp length, and payload from weights. Our example configurator shows all three with sample values of a fictional product; binding figures always come from the manufacturer.
Which options belong to which vehicle type?
The first group of rules is a table: the allowed values per vehicle type. In the example configurator it looks like this:
| Item | Trailer | Horsebox 3.5 t | Horsebox 7.5 t |
|---|---|---|---|
| Horses | 1 or 2 | 1 or 2 | 2 or 3 |
| Stall layout | straight | straight or rear-facing | herringbone or rear-facing |
| Rear ramp | always included | optional | optional |
| Side ramp | no | optional | optional |
| Front unload ramp | optional | no | no |
| Living area | no | none, seating, seating with kitchenette | also with luton bed |
| Tack | none or tack locker | tack locker or tack room | tack locker or tack room |
These are example rules of a fictional product, not a statement about what real vehicles can or may have. For your range you replace this table with your own; it lives in a data file, not in the program code.
What happens when someone changes vehicle type?
Switching from a 7.5 t horsebox with three horses to a trailer leaves an invalid selection. The example configurator handles this in two stages:
- Values that do not fit are disabled and labelled with the reason ("not for this vehicle type").
- The existing selection is adjusted, for example the number of horses to the nearest allowed value, the layout to the first allowed one, or the living area to a smaller level. Each adjustment appears as a short message ("Adjusted: …").
The principle: whoever chose a number of horses, a layout, a living area or tack storage should see why that choice no longer applies.
Which dependencies link layout and ramps?
In a rear-facing layout the horse faces the back; in the example it is loaded via the side ramp on a horsebox. So the rule is: rear-facing on a horsebox switches the side ramp on. A second rule: a horsebox needs at least one loading ramp. Removing both rear and side ramp brings the rear ramp back, again with a message.
Further dependencies in the example: with one horse there is no partition to choose, and the trailer has no living area. On horseboxes with a living area, the review notes that the living area is at the front and the horse area behind a partition wall.
How is the ramp angle calculated?
The angle follows from two values: the height of the loading edge above the ground and the length of the ramp. The angle is the arcsine of loading height divided by ramp length. Worked with the sample values of the fictional demo trailer: a 0.38 m loading edge and a 1.60 m ramp give about 13.7°; with the extension flap and a 1.95 m ramp it is about 11.2°. The higher the loading edge, the more a longer ramp helps.
The configurator shows the angle in degrees live while the ramp lowers; once the ramp is down it adds the gradient in per cent and places it in one of three example bands: gentle below 15°, medium up to 20°, steep above. These bands are an illustrative classification, not a statement on which angle is suitable for horses or required by any rule. Which classification you show, if any, is your decision as the manufacturer.
How does the example payload calculation work?
It is a plain subtraction: gross weight minus unladen weight with the chosen options minus horses minus tack, water and feed. The buyer can adjust the weight per horse and the load. Options such as a tack room, living area or side ramp have an example weight that goes into the unladen weight. When the reserve is low or negative, a message advises checking the weights with the manufacturer.
All weights in the demo are sample values, and the calculation is explicitly not a weight, registration or road-use statement. In a real configurator only figures you as the manufacturer stand behind and approve may appear there. Whether you show payload at all is your call. For the trailer, the towing car appears only as a silhouette, and a note says towing and nose weight are checked by the dealer.
What comes out at the end
The review lists vehicle type, horses, layout, fit-out, ramps, the main ramp's angle, outside dimensions, colours and the example payload, together with the example checks. The enquiry step adds name, company or yard, email, phone, intended use and timing. The text can be copied; the PDF contains an exterior view and a cut-away of the horse area. In the demo your entries are not sent or stored; text and PDF are created in the browser.
Example configurator · fictional product
Horse trailer & horsebox configurator
Put together a horse trailer or horsebox (3.5 t or 7.5 t): number of horses, stall layout, partitions, tack room, living area, ramps, colour and wheels – with a cut-away view, a lowering ramp with an angle readout, an example payload calculation and a PDF enquiry.
The horse trailer and horsebox configurator is an example configurator by Modelwright with a fictional product and sample values. What manufacturers and dealers use it for is covered in horsebox configurator software for manufacturers.
What data you supply for your rules
For your range we need, per model, the allowed numbers of horses, layouts, ramps, living areas and tack options, the loading height and ramp lengths, inside and outside dimensions, your colours and wheels and, if you want a payload calculation, your approved weights. How geometry, animation and the cut-away are built is covered in building a 3D configurator for trailers and vehicle bodies. For hiring us, see custom 3D configurator development.
Frequently asked questions
Can we set our own ramp-angle limits?
Yes. The bands are values in a data file. Whether you show a classification at all, and with which limits, is up to you.
Can dealers see different rules from buyers?
Not in the example. In a project a dealer version with extra options or notes can be set up; we settle that during scoping.
What if we have more than three vehicle types?
The table gets longer; the logic stays the same. Each vehicle type gets its allowed values, and the switching and dependency rules apply to all.


