Louvre configurator rules: sun path, window shading and rules for fixed and rotating blades
The rules an external louvre configurator needs: rotation range, minimum spacing, intermediate support, sun position and the share of the window shaded.
Short answer: a configurator for brise-soleil and external louvres needs two kinds of logic. Blade rules decide which profiles may rotate, how far they can turn before touching, what spacing that needs, and from which span an intermediate support is added. The sun calculation finds the sun's position in front of the facade and tests which part of the window is in shade. Our example configurator does both with example values and labels the result an example calculation.
What are the inputs?
| Input | Example values | Dependency |
|---|---|---|
| Bays | 2 to 6 bays, bay width 1.50 to 3.00 m in 150 mm steps | For horizontal blades this is also the support spacing |
| Height | Window 1.60 to 2.80 m, louvre screen 1.80 to 3.60 m | For vertical blades this is their span |
| Gap to the facade | 150, 300 or 450 mm | Facade only |
| Profile and depth | Aerofoil 150–400 mm, elliptical and rectangular box 100–300 mm, Z-profile 100–200 mm | Sets thickness, whether it can rotate, and the example span |
| Blade spacing | 100 to 600 mm in 25 mm steps | Sets blade count, view through and rotation range |
| Drive | Fixed at 0°, 15°, 30° or 45°; motorised with track the sun, open, closed | Motorised only for aerofoil and elliptical |
| Site | Facade facing SE, S, SW, W or E; 48°, 51° or 54° N (example) | Sun direction relative to the facade |
All values are example values of a fictional product. The default is a 200 mm aerofoil at 200 mm spacing, motorised, tracking the sun.
Which rules apply to fixed and rotating blades?
- Rotation range from the outline. The configurator turns the actual profile outline in half-degree steps and finds the largest angle at which neighbouring blades still keep 4 mm apart. Fixed tilts at which the blades would touch are disabled.
- Motor for rounded profiles only. In the example, rectangular box and Z-profiles are fixed only; the motor button is then disabled, with the reason. Switching to such a profile sets the drive to fixed.
- Minimum spacing for rotating blades. The example rule: spacing at least 0.8 × blade depth. Worked example: a 300 mm aerofoil needs at least 240 mm; at 200 mm the check turns red and suggests increasing the spacing to 250 mm, the next value on the 25 mm grid. One click applies it.
- Intermediate support above an example span. Each profile and depth has an example formula for the free span. If the bay is wider, the configurator adds an intermediate support to the model, lists it in the review and shows a warning. This is a fictional example rule, not a structural design; in your configurator your span tables go here, and they remain the responsibility of you and your structural engineer.
- View through. As a note, the check shows the clear gap between blades at 0°, that is spacing minus blade thickness. For the default that is 200 − 34 = 166 mm.
Rules like these turn a picture into a configurator: nobody can request a combination your range does not offer, and every block comes with its reason.
How are sun position and shading calculated?
The sun is calculated for the 21st of each month at a solar time, from declination, hour angle and the example latitude, then turned into the direction of the chosen facade. When the sun is behind the facade or below the horizon, the readout says so instead of giving a figure.
For the "window shaded" share, the configurator places a grid of points over every pane: 20 × 96 for horizontal blades and 96 × 20 for vertical ones. From each point a ray runs towards the sun and is tested against the rotated blade outlines. Blocked points divided by all points gives the share. Only direct sun is counted, with blades and window mullions, without reflection, reveals, brackets or clouds. The enquiry says exactly that, together with the sentence that the calculation makes no statement on energy, cooling load or indoor climate.
In an independent QA round, the result for a Z-profile at 0° agreed with a separate hand calculation over the middle of the window; at the top edge it is lower because high sun passes over the top blade. That cross-check is a plausibility test, not design data.
Unlike the shade a canopy casts on the ground, this is about the glass and about blade rotation.
What does "track the sun" do?
In tracking mode the configurator raises the blade angle from 0° in 1° steps until 99.5 % of one blade spacing is protected from direct sun, at most up to the rotation range. If that is not reached, it takes the best angle found. "Closed" is the largest angle before the blades touch, at most 80°; "open" is 0°. "Play the day" runs the day as an animation, and the day chart shows the shaded share for every full hour, with hours without direct sun greyed out. Users who have set reduced motion in their operating system see the blades change without the transition animation.
What changes for a louvre screen around plant?
For a screen, the view matters alongside the shade on the equipment face. The configurator also tests what share of the equipment is hidden from 1.60 m eye height at 8 m distance, again as an example calculation.
What does the enquiry contain?
The review, the enquiry text and the PDF list application, blade direction, mounting (with intermediate support where needed), layout, bays, height, gap to the facade, profile with depth and thickness, spacing, blade count and total length, drive, finish, site and the result of the sun check, plus every check. The PDF shows an outside view and a profile view.
Example configurator · fictional product
Brise-soleil & louvre configurator
Plan facade louvres: choose horizontal or vertical blades, profile, depth, spacing, fixed or motorised rotating blades, mounting and finish – then move the sun with the sun-path slider and see the shadow travel across the glass and the share of the window shaded (example calculation).
Try it in the brise-soleil and louvre configurator. Who benefits from such a configurator is covered in brise-soleil and external louvre configurators. Profiles, the sun model and phones are covered in implementing outdoor structure configurators; the project itself in custom 3D configurator development.
Frequently asked questions
Can we use our real profile outlines?
Yes. The outline is a list of points per profile and depth. The same points build the 3D blade and feed the shading calculation.
Does the configurator check spans structurally?
No. In your project it applies the values from your table instead of the example formula, for example per profile, depth and fixing. Structural design stays with you and your structural engineer.
Can an exact site be entered?
The demo offers three example latitudes and five facade directions. Free entry of location, orientation in degrees and date is a project requirement.
Sources
- Modelwright library: brise-soleil and louvre configurator, "Live in this demo" list, read 14 November 2026: modelwright.de/en/library/brise-soleil-configurator/


