Technology

Modular floating dock logic: elements, shapes, draft check and price lines

The rules of a modular floating dock configurator: model, element count, T and L shapes, connectors, accessories per model, a draft check and price lines.

Short answer: a modular floating dock configurator rests on four rule sets. The model fixes element size, deck height and draft. The shape follows from the number of elements in line and across the head, and decides the connectors. Accessories depend on model and shape. Everything becomes price lines with a quantity and a unit price. A check of water depth against draft rounds it off.

Floating dock planner – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

Why does the model come first?

A modular dock is not measured freely; it is built from identical elements. Each model in a series therefore carries a fixed record: element length and width, overall height, deck height above the water, draft, weight, part number and price. Buyers do not choose by those values but by use: swimming and paddling, small boats, bigger boats. A good configurator puts the model choice into the buyer's words and shows the figures alongside for information.

Every further rule follows from the model. Examples of such rules:

  • A model exists only as a single element, so multi-element shapes are not available for it.
  • An accessory fits one model only, such as side cladding matched to the deck height of a particular model.
  • The same accessory has a different version, and so a different price or part number, depending on the model.
  • Elements of different models are not mixed when connectors only join equal widths.

When the buyer changes the model, the configurator has to undo choices that are no longer valid, for example by removing an accessory, and say so in one sentence. Things that disappear silently cause queries.

How are shape and element count set?

InputMeaningDrives
Shapestraight, T or Lwhether a head runs across the end
Elements in line from the shorelength of the dockoverall length, connectors along the length
Elements across the headwidth of the T or Lhead width, connectors across, one joint connector
Direction of the Lleft or rightposition at the shore, space for boats

A simple rule example for connectors: in a straight run every additional element needs one connector, so elements minus one. T and L shapes add a joint connector between the run and the head, plus the connectors within the head. Which kits your system actually needs is your rule; the configurator only does the counting.

Limits belong in the data too: the largest number of elements in line and across the head that you want to sell online. Anything larger is a case for personal advice and should be labelled as such.

In the floating dock planner, straight, T and L shapes come with element counts, and elements are added by tapping glowing slots on the water [1]. Direct interaction adds to the number fields: the buyer sees where the next element goes.

How do accessories depend on model and shape?

  1. Per-piece accessories: swim ladder, bench, bollards. Quantity chosen, price per piece.
  2. Length-based accessories: railing along one side. Quantity follows from the length of the shape, price from a price per metre.
  3. Access: gangways in several lengths and widths, hinged or on wheels. Version and price can depend on the model.

Materials and colours come on top, for example for ladder, bollards and railing. They can change the part number and the look, and sometimes the price. In the demo, gangway (hinged or on wheels), swim ladder, bollards, railing, bench and side cladding can be chosen, with materials and colours for ladder, bollards and railing [1]. One rule worth planning for: offer a colour only once the part has been chosen.

How does the draft check work?

The check compares one buyer input, the water depth at low water at the shallowest point under the dock, with the draft of the chosen model. Three states are enough:

  • No input: the model's draft is shown, so the buyer knows what to measure.
  • Depth greater than draft: the check passes, with the note that bottom, ice and anchoring are assessed on site.
  • Depth less than draft: a clear note that the floats would touch bottom at low water, and the suggestion to choose a deeper spot or another model.

The check is deliberately narrow. It says nothing about whether a dock is suitable for that site and does not replace advice. In the demo, draft and the depth check are fictional sample values, not a structural design and not a quote [1]. Which ratings your configurator shows is your decision as the manufacturer.

How are price lines built?

Every decision becomes a line: name, part number, quantity, unit price, line total. An L-shaped dock of three elements with a gangway gives lines such as "3 × element", "connector along the length", "joint connector", "1 × gangway" and, if chosen, "railing, price per metre × length". The total sits below, with what is not included, such as anchoring, delivery and installation, stated right next to it.

Three rules prevent trouble: keep prices in one currency and in whole units, never show a line without a quantity, and carry the "not included" note into the enquiry. The demo shows a fictional sample price total with price lines [1]. Whether your real prices appear, where they come from and whether dealers see different prices is set in the project; 3D configurators for manufacturers covers where a configurator ends and a quoting system begins.

What goes into the enquiry?

A complete enquiry carries model, shape, element count, overall dimensions, each accessory with its version, the price lines and total, the depth entered with the result of the check, and a notes field for location, boat and timing. In the demo the text can be copied and downloaded as a PDF, and 3/4, plan and side views show the shape [1]. How the enquiry reaches your sales team, dealers or a shop is covered in dock configurator enquiries, site visits and dealers.

Try the example

The floating dock planner is an example configurator by Modelwright with a fictional product and example values. Pick a model, tap a slot, switch to the L shape and enter a water depth.

Example configurator · fictional product

Floating dock planner

Snap a floating dock together from elements: four models, straight, T or L shapes, gangway, ladder and fittings – with a water-depth check, sample price and PDF enquiry.

Docks & marine · Dimensions and sizes · Colours · Materials and finishes

Who such a configurator is for is covered in floating dock configurator software. For a project of your own, see custom 3D configurator development.

Frequently asked questions

Can different models be combined in one dock?

If your system allows it, yes. The rule comes from your data; the configurator applies it.

How are prices updated?

In a project we keep prices in a table separate from the 3D model. We make changes as part of maintenance; an editor for self-maintenance is not offered as standard.

Should element weight be shown?

Only if you stand behind it as product data. It can be useful for transport and installation.

Sources

  1. Modelwright library, floating dock planner, "Live in this demo" list and sample-value note, read 14 November 2026: modelwright.de/en/library/floating-dock-configurator/

Read next