Technology

Modular kitchen grid and layout rules: how a kitchen configurator places units

How a kitchen configurator turns run length and layout into a plausible kitchen: 60 cm grid, unit sequence, corner unit, fillers, island and carcass build.

Short answer: a modular kitchen configurator needs three rule sets. The grid: which unit widths exist and how length is built from them. Placement: which unit goes where, depending on length. Layout: what changes for an L-shape or an island. Stored as data, these rules produce a plausible kitchen for every input, without the user needing to know how to design one. Our example shows it with fixed example rules.

Modular kitchen configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

How does length come from the grid?

In our kitchen configurator, an example configurator with a fictional modular kitchen built by Modelwright, the run is planned in whole 60 cm base units: at least 4, at most 8, so 2.40 to 4.80 m. A tall unit with an end panel always closes the run on the right, wall units hang above, and an extractor sits over the hob. The user does not choose centimetres but a number of units. That is deliberate: a length that does not exist as units can never be offered.

For your range we would use your real widths, perhaps 30, 45, 60 and 90 cm, and derive the length options from them. If prospects are to enter wall lengths, fillers are added to take up the difference between grid and wall.

Which units follow from the length?

The demo fills the run from left to right in fixed sequences, stored as a table in its data:

UnitsBase unit sequence (before the tall unit)
4sink · dishwasher · hob · drawers
5door · sink · dishwasher · hob · drawers
6drawers · sink · dishwasher · drawers · hob · drawers
7door · drawers · sink · dishwasher · drawers · hob · drawers
8door · drawers · sink · dishwasher · drawers · hob · drawers · door

Two example rules are built in: the dishwasher always sits next to the sink, and the hob has drawer units beside it. For a real kitchen, makers write rules like these as conditions, such as "dishwasher next to sink", "hob not next to a tall unit" or "minimum worktop beside the hob". A fixed sequence per length is the simplest start; conditions are more flexible but need more testing.

What changes for an L-shape or an island?

  • L-shape: a leg of three base units (drawers, door, drawers) is added along the left wall. A corner unit fills the corner, and fillers in the front finish keep fronts and handles from clashing there. If the run starts with a drawer unit, it becomes a door hinged away from the corner.
  • Island: the hob moves from the run onto the island and drawers take its place in the run. The island has three units (drawers, hob, drawers) from 6 units upwards, otherwise two. Between the run's worktop edge and the island there is a fixed 1.20 m in the demo, an example value.

Which clearances, corner solutions and minimum sizes apply to your range is yours to set; the configurator applies your values.

Example configurator · fictional product

Modular kitchen configurator

Plan a modular kitchen: single run, L-shape or with island, run length on a 60 cm grid, fronts, handles and worktop – with opening fronts and the carcass build-up.

Furniture in the buyer’s room · Dimensions and sizes · Colours · Materials and finishes

How do fronts, handles and worktop interact?

Fronts (five finishes), handles (recessed grip, bar, knob) and worktops (solid oak, terrazzo-look stone, stainless steel at 12 or 40 mm) can be combined freely in the demo. One dependency shows in the geometry: with the recessed grip, the units get an aluminium grip channel profile; the other handles sit on the front. Fillers and the end panels of the run take the front finish; the island's end panels are in the worktop material. Your range would add typical exclusions, such as worktop thicknesses only available in certain materials.

What does the carcass build-up show?

"Carcass build-up" takes a unit apart and labels it: 19 mm side panel, grooved back panel, rails, aluminium grip channel profile, inner drawer, full-extension soft-close runners, adjustable feet, plinth panel, 19 mm front and a steel-sided drawer box. In the demo these labels are in German, and they are example values of the fictional range. For a maker this is where carcass quality can be shown; names and sizes would then come from your engineering.

How is the 3D model produced?

Five lengths, three layouts, five fronts, three handles, three worktops and two thicknesses cannot be handled as a library of finished models. In the demo, code assembles every unit from parts: each unit type (drawers, door, sink, dishwasher, hob, tall, wall, extractor, corner) has a build function that creates panels, shelves, fronts, handles and interior. Change the length and the units are re-placed; change the front and only the material swaps. For your range, those build functions follow your construction sizes. Further implementation questions, from materials to load time and collection updates, are covered in furniture configurator implementation.

What is missing for an enquiry?

The demo ends at the view. For a project we would propose a summary with layout, unit count and length, unit sequence, front, handle, worktop and thickness, plus contact details and a preferred appointment, sent by email or webhook to the showroom or sales team. The industry view is in kitchen configurator for kitchen manufacturers; how a project runs is under custom 3D configurator development.

Frequently asked questions

Why a fixed sequence rather than free design?

Because it always produces a plausible kitchen and is quick to build. Free placement with conditions is possible but needs more rules and test cases.

Is the 1.20 m island gap a recommendation?

No. It is a fixed example value in the demo. The clearances you recommend are for you as the maker, or your kitchen designer, to set.

Can special widths be handled?

Yes, as extra unit widths in the grid and with fillers for leftover lengths. Each new width extends the placement rules.

Sources

  1. Demo features: "Live in this demo" list on the kitchen configurator library page, read 14 November 2026: modelwright.de/en/library/kitchen-configurator/
  2. Grid, placement and labels: demo source code (kitchen/source/kitchen.source.js: LIMITS, AISLE, runSequence, L-shape and island build; kitchen/runtime/kitchen.js: EX_LABELS), read 14 November 2026.

Read next