Technology

Pallet racking layout: pallet positions, aisle width and clear height as configurator rules

How a pallet racking configurator counts positions: aisles from hall width and truck, bays, level pitch, clear-height checks and one-click suggestions.

Short answer: a pallet racking layout can be planned in a configurator with a handful of rules. Hall width, aisle width and frame depth give the number of aisles and rows; hall length gives the bays; load height and frame height give the levels. Pallet positions are then rows × bays × levels × pallets per bay. Three checks keep the plan honest: clear height, the truck's lift height and the aisle width. Our example configurator shows this with example values for a fictional product.

Pallet racking configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

Which inputs does a pallet racking installation have?

InputIn the demo (example values)In a project
Hallwidth 12–40 m, length 15–60 m, clear height 5–14 m; three example hallssizes from the operator's hall drawing
Truckcounterbalance (aisle 3.60 m, lift up to 6.0 m), reach (2.90 m, 10.0 m), very narrow aisle, guided (1.80 m, 12.5 m)values from the data sheet of the truck in use
Layoutwall runs plus double runs, double runs only, single runs only; aisles and bays up to the maximum that fitsyour standard layouts
Pallet and bayEuro pallet 1200 × 800 or industrial pallet 1200 × 1000 mm; 2 or 3 pallets per bayyour beam lengths
Frames and levelsframe depth 1.0/1.1/1.2 m, frame height 2.5–14 m, 2–9 levels, load height 0.9–1.8 m, lowest level on the floor or on beamsyour frame catalogue in its hole pitch
Accessories and coloursmesh decking, column guards, end barriers, labels; three frame and three beam coloursyour option list

Every value is an example value of a fictional product, not a planning rule and not a load table. In reality the truck maker states the working aisle.

How many aisles and rows fit into the hall?

The demo works across the hall. It takes 0.15 m off each side for the gap to the wall, then tries how many aisles fit with the chosen layout. With "wall runs plus double runs" there is a single run on each wall and double runs in between, with 0.20 m between the two backs. Whatever is left over appears in the hall plan as free area.

The truck has the biggest effect here. In the default set-up (24 m wide hall, 1.1 m frame depth, reach truck with a 2.90 m aisle) four aisles and eight rack rows fit. Switch to the counterbalance truck and the demo sets the aisle to its 3.60 m example value: only three aisles and six rows fit, and the positions drop from 1,320 to 990. The very narrow aisle truck with its 1.80 m aisle gives five aisles and 1,650 positions; in the model, guide rails then replace the floor markings in the aisles.

Aisles and bays start at "as many as fit". Buyers can reduce them with the minus button; the demo does not allow more than fit.

How many bays does a run have?

Along the hall the demo reserves 4.0 m at the front for the main aisle and 0.6 m at the back. Bay width follows from the beam: for Euro pallets 1.825 m for two and 2.70 m for three pallets, for industrial pallets 2.225 m and 3.30 m (example clear beam lengths), plus the upright. In the 36 m example hall that gives 11 bays of three Euro pallets each.

How are levels and heights worked out?

The level pitch comes from load height, pallet height, a clearance for storing and retrieving and the beam height, rounded up to 50 mm. With a 1.20 m load height the demo arrives at 1.60 m. If the lowest level sits on the floor, the first beam is at 1.60 m; if it sits on beams, the first one is at 0.20 m. The frame must reach at least 0.25 m above the top beam. Add levels beyond that and the demo raises the frame, as long as it still fits under the clear height.

Which checks belong in it?

  • Clear height: the top of the highest load plus a 0.50 m example clearance must stay below the clear height. By default that is 7.74 m + 0.50 m in a 9.0 m hall. Go to six levels and the check turns red; the demo suggests five levels, or a lower load height if no level count works.
  • Lift height: the highest storage level must be within the truck's example lift height. With the counterbalance truck the top level in the default set-up is at 6.40 m, above its 6.0 m, and the suggestion is the reach truck.
  • Aisle width: set the aisle narrower than the truck's example value and it turns red; the suggestion resets it with one click.
  • Pallet overhang: as a warning, the demo checks that the pallet overhangs the frame by 50 to 100 mm on each side (example rule).

Each suggestion is applied with "Apply". The demo labels every check as an example rule that does not replace planning, load calculation or acceptance. In a project, the rules come from you.

What does the sample calculation per level show?

The buyer picks one of four example pallet weights (300, 500, 800 or 1,000 kg). The demo multiplies it by the pallets per level and by the levels: 3 × 800 kg gives 2,400 kg of goods per level and bay, and with five levels 12,000 kg of goods per bay. That is arithmetic on example data and explicitly not a load rating. In a project it becomes a lookup in your load tables (beam, span, level), in your own wording.

What comes out at the end?

The review lists hall, floor area, truck, aisle width, layout, rows and bays, the positions with their calculation, pallet, bay, frame, levels, accessories and every check. From that the demo builds an enquiry text to copy and a PDF with the hall view and the hall plan. Name, company, email, phone and the type of project (new hall, extension, refit or replacement, not decided yet) are added. Inputs are not sent; text and PDF are created in the browser.

Example configurator · fictional product

Pallet racking configurator

Plan a pallet racking installation for a warehouse: enter the hall and its clear height, choose the truck and aisle width, set single and double runs, bays, frames and levels – with a live pallet-position count, a hall plan with aisles and a truck that stores a pallet.

Partitions, guarding & shelving · Dimensions and sizes · Colours · Options, modules and accessories

Who such a configurator suits and which features it needs is covered in pallet racking configurator software. How model, data and mobile display are built for installations like this is described in implementing configurators for stores, booths and enclosures. For hiring us, see custom 3D configurator development.

Frequently asked questions

Can the configurator follow our hole pitch?

Yes. The demo rounds the level pitch to 50 mm. In a project your frame heights in their hole pitch and your rules for levels and clearances replace those example values.

Is there a parts list?

The demo shows none. A list of frames, beams, decks, anchors and guards can be derived from the same geometry in a project.

What counts as clear height?

The demo explains it as the distance from the floor to the underside of trusses, lights or sprinklers, whichever is lowest. Which clearances apply in a particular hall is for the operator and planner to settle under local rules.

Sources

  1. Demo features: "Live in this demo" list on the pallet racking configurator library page, read 15 November 2026: modelwright.de/en/library/pallet-racking-configurator/
  2. Rules, example values and default set-up: demo source code (data.js: HALL, TRUCKS, PALLETS, gaps; app.js: geo(), checks(), suggestion()) and schema notes, recalculated 15 November 2026.

Read next