Technology

Pivot door sizing and swing logic: how a configurator should calculate it

How a pivot door configurator turns a structural opening into a door size, swing and passage, which rules a maker supplies, and what the enquiry carries.

Short answer: a pivot door configurator works outside-in. The structural opening, minus any side and top panels, gives the door size; the door size, pivot side and opening direction give the swing and the passage; only then do faces, finishes and hardware come in. Every rule along the way is one line of condition, consequence and message. The maker supplies those lines, and the configurator enforces them.

Pivot front door configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

What order should the steps follow?

Order matters because each step limits the next. A buyer who picks a finish first and types the opening last will end up with doors that do not fit the wall. The sequence we recommend:

  1. Opening: structural width and height; side panels left, right, both or none; top panel or not.
  2. Door: leaf width and height, calculated from step 1 and held within your size limits.
  3. Movement: pivot side and opening direction, giving the swing area and the usable passage.
  4. Build: how the pivot is fitted, for example recessed or flush.
  5. Design: door face, material and finish, handle, lock, glass in side and top panels.
  6. Checks and enquiry: notes on position and combinations, a summary, the enquiry.

Our pivot door configurator, an example configurator with a fictional product and example values, covers the building blocks of this pattern.

Which values depend on which?

The table below shows how to write the dependencies down for a real product. It is a proposed template for your specification, not a description of the numbers inside our demo: the actual limits always come from your own data.

ValueDepends onRule (form, not figure)What the buyer sees
Leaf widthOpening, side panels, frameOpening less side panels less frame, within your limitsCalculated; a note when outside the range
Leaf heightOpening, top panel, thresholdOpening less top panel less fixingsAs above
PassageLeaf width, pivot offsetDerived from leaf width and pivot positionShown as an estimate
Swing areaLeaf width, pivot side, directionArcs around the pivotDrawn on the floor
FinishDoor face, materialReleased pairs onlyOthers greyed out or flagged
HandleMaterial, faceSome handles only with some materialsLocked with a reason
PositionExposure, finish, buildRelease per positionA check with a note

Keep two kinds of rule apart. A combination you never make should not be selectable at all. A combination that works only under conditions, such as a finish on a door that faces the weather, should stay selectable but carry a clear note into the summary and the enquiry. That tells your sales team exactly what to discuss.

Why handing deserves its own rule

Pivot side and opening direction together define the handing of the door, and they are easy to confuse: left or right is normally described from one agreed side, and "opens in" or "opens out" from the same side. A configurator should state the reference side next to the choice and repeat it in the enquiry. One vendor makes a related point: Threekit's door page says its software "writes the handing code, so reps and dealers do not have to select the code themselves" [1]. In a bespoke build the equivalent is simple: one source of truth for the reference side, and the swing drawn so nobody has to imagine it.

What the demo shows

As listed on its library page [2], the example configurator covers the structural opening with side and top panels, the door size from the opening, pivot side and opening direction with the swing and a walk-through estimate, a recessed or flush pivot build, four sample door faces, hardwood, RAL or bronze finishes, handles, locks and glass, an exposure check with example rules, and enquiry text plus a PDF. The swing and exposure checks are example rules, not a code check and not a quote.

Example configurator · fictional product

Pivot front door configurator

Plan a pivot front door: structural opening with side and top panels, four door faces, pivot side and direction with a walk-through estimate, finishes and hardware – with a PDF enquiry.

Doors & openings · Dimensions and sizes · Colours · Materials and finishes

What data does the maker supply?

You do not need a software specification. The documents your sales team already uses are enough to start:

  • Size limits per door type: minimum and maximum width and height, and any size steps.
  • Opening build-up: how side and top panels share the opening, with frame and fixing allowances.
  • Pivot position per leaf width or build, so the swing and passage can be calculated.
  • Pivot builds with a drawing of each.
  • Design options: faces, materials, finishes, handles, locks and glass, each with the combinations you allow.
  • Releases per position, for example sheltered or exposed entrances, as your sales team applies them today.

How the geometry, the swing animation and the plan view are built is covered in implementing door, gate and window configurators.

What the enquiry should carry

The same rows as the summary: opening, side and top panels, leaf size, pivot side and direction with the reference side, build, face, finish, handle, lock, glass, position, and every note the buyer saw, plus a picture of the door. In the demo the enquiry text can be copied and downloaded as a PDF; in a project they go to your sales team by email or webhook.

Why and for whom such a configurator is worth building is covered in front and pivot door configurator software. For a project of your own, see custom 3D configurator development.

Frequently asked questions

Is the passage width exact?

In the demo it is an estimate based on example values. In a project it uses your dimensions; the site survey stays binding.

Can the rules be changed later?

Yes. Rules are stored as data and can change without rebuilding the model. A self-service editor is not standard; we make the changes.

Does the configurator check standards or security ratings?

No. It applies the releases you give it. Evidence on security, thermal performance or standards stays with the manufacturer.

Sources

  1. Threekit, "Door and Window Quoting for Reps and Dealers", read 14 November 2026: threekit.com/industry/door-configurator-software
  2. Modelwright library, pivot door configurator, "Live in this demo" list, read 14 November 2026: modelwright.de/en/library/pivot-door-configurator/

Read next