Stall front configurator rules: door swing, aisle clearance and option fit
The rules a horse stall front configurator needs: hinged door reach into the aisle, sliding door overlap, yoke and feeder fit, row length, units.
Short answer: a stall front configurator needs three kinds of rule: space (does the open door need more room than the aisle or the next stall can give?), fit (which yoke and which feed opening go with which front?) and quantity (stall size times count gives the row). Just as important is what happens on a conflict: it should be visible and travel with the enquiry as a question, not stop the enquiry.
How does the aisle check work?
Our example configurator uses a fictional product and example values. Its library page lists series A with a sliding door or series B with hinged low or high fronts, style options, stall width, depth and count, aisle width, and aisle clearance and review checks. The logic below is what we propose for a manufacturer's configurator.
A hinged stall door swings into the aisle and needs roughly its own width there. A sliding door stays on the front. The check therefore compares how far the open hinged door reaches into the aisle with the aisle width the buyer entered:
| Situation | Proposed result |
|---|---|
| Hinged door, aisle wide enough | Green, with the clear width that remains |
| Hinged door, aisle too narrow | Red; the swing is drawn on the floor and the note points to a sliding door as an alternative |
| Sliding door | Green: the aisle stays clear when the doors are open |
| No aisle width entered | A prompt to enter one; nothing is assumed |
This is deliberately simple. It does not say whether horses can be led safely along that aisle, what width your company recommends, or what any authority or association advises. If you want such a value shown, it comes from you, and you are responsible for it.
What can go wrong with a sliding door?
Sliding doors have a conflict of their own: when opened, the door slides across the front of the neighbouring stall. If the stall is narrow and the door sits on the wrong side, the open door would overlap the next stall's door. With two or more stalls a configurator can check this and suggest a wider stall or another door position.
How are options tied to fronts?
Not every option suits every front. Two examples:
- Yoke. It is only available on certain fronts. Switch to a front without that possibility and the configurator sets the yoke to "No yoke" and says why.
- Feed opening. Whether a swivel grain feeder, a grill feed door or a plain feed hole fits depends on the space in the front panel at that point. If the chosen opening does not fit, the configurator picks one that does and notes the change.
Rules like these are easy to write down when your design already defines them: "option X only with front Y", "opening needs at least this much panel". In a project we keep them as data where possible, so that a new series mainly means new rows in a table.
How are sizes and quantities handled?
Stall width and count give the row length, including the end post or end column. Entries outside the allowed range should be limited with a note. Units follow your markets, for example feet and inches or millimetres, with the other unit shown alongside in the summary if you wish. For a real project this is the start of a parts list: fronts, partitions, infills and hardware per stall with your part numbers. That is a proposal.
What happens to a red check?
A conflict should not block the enquiry. We suggest listing red checks in the enquiry text as an open question to the manufacturer. That suits stall fronts, because some conflicts can be solved in conversation, for example by changing the aisle layout of the barn. Your sales team sees at once what needs discussing.
What data do you supply?
- Series and door styles with their dimensions
- The stall sizes you offer, and the steps in between
- Door logic: hinge side, sliding direction, door positions
- Infills, feeding systems and yokes, with the fronts they fit
- Colours, timber and plastic infills, rust protection options
- The figures your sales team uses today when discussing aisle widths
What comes out at the end?
The summary should show the front, stalls, row length, heights, door, infills, options and finishes. The enquiry text then repeats those rows, lists open questions from the checks, and asks for price, lead time and freight, with lines for name, phone and postcode. In the demo, the enquiry text can be copied and downloaded as a PDF.
Example configurator · fictional product
Horse stall fronts configurator
Put together horse stalls: sliding or hinged fronts, stall width, depth and count, aisle, fills and colours – with door and feeder animations, checks and a PDF enquiry.
Try it in the horse stall fronts configurator. Who it is for is covered in horse stall configurator software. How animations, units and phones are handled is in building a configurator for equestrian and livestock products. For hiring us, see custom 3D configurator development.
Frequently asked questions
Does the configurator give a minimum aisle width?
The demo does not; its aisle check uses sample values. If you want a recommendation shown, the value comes from you.
So is a sliding door always better?
No. It has its own limits, such as the space in front of the next stall. A configurator should show both conflicts; the recommendation stays with your sales team.
Can it handle facing rows?
The demo covers one row of stalls with its aisle. Facing rows, and an aisle check between two swinging doors, can be built in a project.
Sources
- Modelwright library: horse stall fronts configurator, "Live in this demo" list (read 14 November 2026): /en/library/stall-fronts-configurator/


