Technology

Standing desk configurator logic: height range, add-on rules and the fit check under the top

How a sit-stand desk configurator handles the height range, column and monitor rules, add-ons under the top and a scope of delivery from one plan.

Short answer: a configurator for sit-stand desks needs four building blocks: a height range the frame visibly travels in the model, rules that tie frame and add-on variants to the top size, a fit check that tests the add-ons under the top against the lowest height, and a scope of delivery from the same plan. Our example configurator shows all four with example values. The principle: a check does not just flag a problem, it names the cause and suggests a fix.

Desk configurator (sit-stand desk) – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

What does the example take as input?

InputExample valuesAffects
Top width1,200, 1,400, 1,600, 1,800 or 2,000 mmnumber of columns, monitor arm, cable tray, panel
Top depth700, 800 or 900 mmposition of the cable tray relative to the pedestal, footprint
Shaperectangular (R 6), rounded (R 100), curved front (70 mm cut-in)top outline
Frame2 or 3 three-stage lifting columns, four colours; single desk or benchmodel, scope of delivery, footprint
Desk height650–1,250 mm in 10 mm stepscolumns, cable spine, figure
Cablescable tray (full width or up to the pedestal), cable spine, two 80 mm grommetslowest height, scope of delivery
Add-onsfelt panel in six colours, monitor arm none, single or dual, mobile pedestal, CPU holder, power modulerules, lowest height, scope of delivery

All values are example values of a fictional product. The top is 25 mm thick; width and depth are picked in fixed steps, not typed in.

How does the configurator show the height range?

The example frame moves the top surface from 650 to 1,250 mm. The buyer sets the height with the slider or in 10 mm steps with plus and minus in the height readout. In the model the middle and inner stages of the columns extend, the cable spine follows the height, and the value appears in the readout and on the handset at the desk, each labelled as an example value. If the camera is under or above the desk at that moment, it moves to the side view.

Two buttons move the desk to the example positions "Sit" (720 mm) and "Stand" (1,100 mm). Both belong to a fictional 1.75 m figure and are not a recommendation; the demo makes no statement on ergonomics or health. From 880 mm the figure stands, below it sits. On the way up it stands at once and the chair rolls back; on the way down it only sits once the desk is low enough. The animation is sped up. The figure is there for scale and can be hidden.

Which rules tie the frame and add-ons to the top?

RuleExample valueBehaviour
Middle columnfrom 1,800 mm top widthdisabled below that, with the note "from 1,800 mm width"
Dual monitor armfrom 1,400 mm top widthdisabled below that, with the note "from 1,400 mm width"
Top made narrowerchoice no longer validswitches back to 2 columns or one monitor, with a message
Add-ons under the toppedestal raises the lower limitif the desk is lower, it moves up to the new lower limit, with a message

With three columns the workplace moves to the left bay between the columns; the figure and the monitor move with it in the model. A bench is two identical desks back to back with a shared panel. In the example both tops move together, and the footprint is the top width by twice the top depth plus a 10 mm joint, without chair space; at 1,600 × 800 mm that is 1,600 × 1,610 mm.

How does the check under the top work?

Under the top, the frame's cross rail, the cable tray and the mobile pedestal share the space. In the example the pedestal is 420 mm wide, 560 mm deep and 590 mm high and stands 60 mm back from the front edge. The tray is 160 mm deep and 110 mm high and starts 30 mm in from the back edge, so it needs the rearmost 190 mm. From this the demo works out the lowest height:

  • No pedestal: 650 mm, the lower limit of the frame.
  • Pedestal under the cross rail: 590 mm pedestal, 10 mm gap, 45 mm from the underside of the top to the underside of the cross rail and a 25 mm top make 670 mm.
  • Tray above the pedestal: the pedestal reaches 620 mm back from the front edge. With a 700 or 800 mm deep top, less than 190 mm is left behind it, so the tray sits above the pedestal. Then it is 590 mm pedestal, 10 mm gap, 110 mm tray plus 5 mm and a 25 mm top: 740 mm in total.

At 740 mm the 720 mm "Sit" example position can no longer be reached. The demo shows this in several places: the check in the review and the height readout are marked as a warning, the slider gets a red zone below the lower limit, and in the model a "Lower limit 740 mm" label sits on the pedestal. The one-click suggestion appears in the Height, Cables and Add-ons steps. It shortens the tray so that it ends 40 mm before the pedestal; the lower limit drops to 670 mm, and if the desk is in the sitting position it moves to the 720 mm example position. At 1,600 mm top width the tray is then 790 mm long instead of 1,200 mm. A 900 mm deep top avoids the overlap without shortening anything.

This check is a geometric example calculation from part sizes. It makes no statement on load capacity or standards. In a project your frame and add-on sizes and your own parts, such as extra cable channels or pull-outs, go into it.

Example configurator · fictional product

Desk configurator (sit-stand desk)

Put together an electric height-adjustable desk: choose the top, frame, height, cable management and add-ons, and watch the desk move between sitting and standing height.

Furniture in the buyer’s room · Dimensions and sizes · Options, modules and accessories · Materials and finishes

Why does the view change on its own?

Many add-ons sit out of sight in an angled view, so the demo moves to the changed part: for the cable tray, cable spine, pedestal and CPU holder the camera goes under the desk; for grommets, power module, shape and surface it looks from above; for the height it moves to the side if the camera is under or above the desk at that moment. The figure is hidden in the Under and Top views. The buyer can switch between 3/4, Side, Under and Top at any time, show dimension labels and reset the view.

What is in the scope of delivery?

The example scope of delivery comes from the same plan as the model. It gives item, quantity and version: desktop with size, shape and surface, lifting frame with number of columns, colour and height range, control box with handset and height display, cable tray with its length, cable spine, grommets, panel with clamps, monitor arm, mobile pedestal, CPU holder and power module with a flip-up lid. For a bench the per-desk quantities double, and the shared panel appears once. The review above it states the height range with the chosen add-ons and the footprint.

For a project, the list is the test: if it matches your sales office's order entry for the default and a few edge cases, such as a 2,000 mm bench with three columns or a 700 mm deep top with a pedestal, that is a good sign the logic behind it is right.

What does a project add?

The demo ends with a review, an enquiry text and a PDF with a 3/4 and a side view. For your range we would add your frames with their stage count, height range and column variants, your top sizes, shapes and finishes in place of the example textures, your add-ons with real part sizes in the fit check, a scope of delivery with item numbers and an enquiry by email or webhook. Modelling, materials and load time are covered in Building furniture and room configurators, the sales view in Desk configurator for office furniture makers and the project process on 3D configurator development. The demo itself is on its library page.

Send us your frame data and a list of add-ons with sizes, and we will reply with a proposal for the logic and a fixed-price quote.

Frequently asked questions

What happens if the buyer adds the pedestal first and changes the depth afterwards?

With a pedestal and a full-width tray, switching from 800 to 900 mm depth drops the lower limit from 740 to 670 mm; going back to 800 mm brings back 740 mm and the suggestion.

Does the animation show how the real frame moves?

No. The animation is sped up so that the sequence takes only a few seconds.

Can we add our own accessories?

Yes. In the example each add-on is its own building block with its own control, model and line in the scope of delivery. Further parts are added the same way; if they sit under the top, their sizes can go into the calculation of the lowest height, as the pedestal and tray do in the example.

Sources

  1. Demo features: "Live in this demo" list and note on the desk configurator (sit-stand desk) library page, read 18 November 2026: modelwright.de/en/library/desk-configurator/
  2. Height range, rules, check and scope of delivery: demo source code (data.js: WIDTHS, DEPTHS, RULE; app.js: minH, norm, checks, suggestion, parts) and schema notes, read 18 November 2026; sequences from the logs of the QA rounds of 17 November 2026, emulated devices.

Read next