Banquette cover count and aisle check: the rules inside a booth seating configurator
The rules a booth and banquette configurator calculates: covers from run length, bench depth, clear aisle, room width and table-minus-seat height.
Short answer: a banquette configurator rests on four rules. Covers: how many guests does a run of seating hold? Depth: how far into the room do bench, table and chairs reach? Aisle: what is left to the opposite side? Heights: do seat and table suit each other? Each can be written as a formula with planning values. Our example configurator runs all four with example values; the real values come from the manufacturer and the designer.
What goes into the calculation?
- Layout: single booth, booth row (2–4 booths), L-corner, U-booth, curved booth or wall banquette. It decides which formula applies.
- Run length: per layout, for example 1.80–7.20 m for a wall banquette or 1.00–2.00 m for a booth bench; steppers move in 100 mm steps, typed values are rounded to 50 mm. Typed values are accepted in metres, centimetres or millimetres.
- Side length: for the L-corner and the U-booth.
- Seat depth 480, 520 or 560 mm; seat height 430–470 mm; table height 740–760 mm.
- Room width and depth: 3.60–12.00 m and 3.00–9.00 m.
- Minimum aisle: 0.90 or 1.20 m, both example values.
Room depth is defined in the demo as the distance from the wall behind the bench to the opposite wall, counter or furniture. Put that definition into every enquiry; otherwise a designer may measure something else.
How are covers counted?
The base rule in the example is 600 mm of seat width per cover, an example value. From that:
| Layout | Rule (example) | Worked case |
|---|---|---|
| Booth | bench length ÷ 600 mm, rounded down, × 2 benches | 1.40 m bench: 2 per bench, 4 per booth |
| U-booth | back bench by its usable width, each side by its length less the bench depth plus 300 mm | 2.40 × 1.90 m U: 7 covers |
| Curved booth | by the arc length at the back cushion face | – |
| Wall banquette, L-corner | by the tables along the bench, with chairs opposite; tables 0.70 m (two) or 1.20 m (four), 0.30 m apart | – |
The review states the result together with the basis, for instance "8 covers at 2 tables" for the default two-booth row, so nobody reads it as a promise.
How do bench depth and aisle come out?
In the example, bench depth is 220 mm for the back shell and back cushion plus the chosen seat depth: 740 mm at a 520 mm seat. A booth is two bench depths plus a 750 mm table wide, less the table edge that overlaps each seat front by 50 mm.
How deep the seating zone reaches depends on the layout. For booths standing at right angles to the wall it is the bench length; for a wall banquette it is bench depth plus a 0.70 m table less the 50 mm overlap, plus a 600 mm zone for the chairs opposite; for the U it is the side length. The clear aisle is room depth minus seating zone. With the defaults: 4.20 m − 1.40 m = 2.80 m.
If the aisle falls below the chosen example minimum it turns red in plan view, and the review gives the shortfall with a hint: shorter sides, another layout or a deeper room. One test case from QA: a 2.40 × 1.90 m U-booth in a 3.00 m deep room with a 1.20 m minimum leaves a 1.10 m aisle, red. The width check compares the seating group with the room width and flags any overrun.
This is a planning aid, not a plan. Which aisle widths and escape routes apply on site is decided by the designer and the operator. The configurator can only apply the values you give it as the manufacturer.
How are heights checked?
The height check compares table height minus seat height with an example comfort band of 270 to 320 mm. A 750 mm table over a 450 mm seat gives 300 mm, inside the band; outside it, the review shows a warning and suggests adjusting seat or table height. "Guest" slides a seated figure (1.75 m, example) onto the bench, and the profile view labels the table-to-seat gap and an approximate eye height. It does not replace sitting on a sample; it shows when two chosen values plainly do not go together.
What goes into the enquiry?
The review lists every value, every check with its result and a note that these are example values. The enquiry text copies each row verbatim, plus name, company, email, phone, number of seating groups and project notes. The PDF has two pages: 3D view and plan with the aisle first; review, checks and contact second. In the builder's QA every review row appeared verbatim in the enquiry text and in the PDF's text; the independent round confirmed this for the enquiry text.
Example configurator · fictional product
Booth & banquette seating configurator
Plan restaurant banquettes and booths: choose layout, length, back and cover, and see in plan at once how many covers fit and whether the aisle stays wide enough.
What does your data replace?
For your range, your models replace the combinations of back style and end panels, your module lengths replace the free lengths, your fabric and vinyl books replace the colour list, and your planning values (seat width per cover, table overlap, the aisle minimums of your market) replace the example rules. Because those values live in a data file and the geometry is built from them, the range can be maintained without rewriting the logic. Upholstery geometry, materials and load time are covered in furniture configurator implementation; the industry view is in booth seating configurator for contract seating makers; how a project runs is under custom 3D configurator development. The live demo is on the library page.
Frequently asked questions
Where do 600 mm, 0.90 m and 1.20 m come from?
They are the demo's example values and carry no guarantee. For your range we use your own planning values; local requirements are for the designer to confirm.
Does a red check block the enquiry?
No. The enquiry carries the red check as information, which tells your sales office exactly what needs discussing.
Can special shapes be added?
Yes, as an extra layout with its own cover and depth rule. Each one needs its own test cases.
Sources
- Demo features: "Live in this demo" list on the booth and banquette configurator library page, read 14 November 2026: modelwright.de/en/library/booth-seating-configurator/
- Rules, ranges and defaults: demo source code (data.js: RULE, AISLE_MIN, LAYOUTS, ROOM; app.js: plan and checks) and schema notes; test cases: QA log of 14 November 2026 (builder and independent rounds, emulated devices).


