Industries & use cases

Wardrobe configurator for built-in wardrobe makers and joiners: features, benefits, build

What a 3D wardrobe configurator needs for made-to-measure built-ins: niche, sloped ceiling, sections, doors, fit checks, parts list and enquiry.

Short answer: a wardrobe configurator earns its place at a built-in wardrobe maker or joinery when it starts from the niche, not from the catalogue. The buyer enters width, height, depth and any sloped ceiling; the configurator divides the wardrobe into sections you can build, shows doors, fronts and fittings on the model, and flags at once when a door would hit the wall or a hanging rail will not fit. It ends in an enquiry with sizes, check results and a parts list. It does not replace measuring on site.

Built-in wardrobe configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

Who is a wardrobe configurator for?

This guide is for managing directors, sales and product leads at makers of built-in and sliding-door wardrobes, for joiners who build fitted wardrobes to measure, and for online retailers selling made-to-measure storage. Their buyers are homeowners with an alcove in the hall, a bedroom in the loft or a dressing area, plus interior designers and developers fitting out several flats.

A fitted wardrobe is not stock furniture. It is built for one room, and every enquiry starts with a question the buyer can rarely answer with confidence: what will actually fit in my niche?

What makes fitted wardrobes different from other furniture?

  • The niche sets the size. Width, height and depth come from the room, often with tolerances and walls that are not quite square. The wardrobe has to absorb them with filler panels, a plinth and a ceiling filler.
  • A sloped ceiling changes everything. Under a slope, sections get lower, doors and back panel are cut at an angle, and some door types stop being possible.
  • The wall has a say. A hinged door right next to a wall needs room for the door thickness and the handle. Without it, the door hits the wall. No photo shows that.
  • The interior is planned, not just picked. A hanging rail needs clear height; a rail running across needs depth. What fits in a section depends on that section's size.

Without a configurator, these questions wait for the phone call or the first visit. A configurator asks them earlier, in the order you would plan the job yourself.

Which features does it need, and what does our example show?

FeatureWhyIn the example configurator
Niche size and sloped ceilingstart from the roomyes: width, height, depth with plus/minus and typed input; slope on the left or right with knee wall height and pitch
Division into sectionsbuildable widths onlyyes: automatic equal sections or a chosen number, width shown
Filler panels, plinth, ceiling fillertake up the nicheyes: fillers left and right, plinth none, 60 or 100 mm, ceiling filler for tall niches
Door system and handleshow your rangeyes: hinged doors, sliding doors on two tracks or open compartments; grip groove, bar handle or knob
Fronts and carcasschoose the finishyes: six lacquer colours, oak, walnut and ash veneer, mirror; carcass inside white, light grey or oak decor
Fittings per sectionplan the storageyes: rail with hat shelf, two rails, shelves, inner drawers, shoe pull-outs; LED light top or side
Fit check with suggestionscatch problems before the surveyyes, live, with one-click suggestions
Parts list, enquiry text, PDFan enquiry without follow-up callsyes: example parts list, text to copy, PDF with closed and open views
Your pricesprice rangeno, added in a project

What does it bring?

We do not promise figures. The benefit lies in work that every made-to-measure enquiry creates today:

  • The enquiry arrives with the niche. Sizes, slope, sections, door type and fittings are in the enquiry, so the first call is no longer about how wide the alcove really is.
  • Problems show up early. If the buyer wants sliding doors under a slope, the configurator explains why that does not work. If a filler is too narrow for the chosen handle, it turns red before anyone writes a quote.
  • Buyers see what they are buying. The doors open in the model and the fittings are lit. That does not replace a showroom visit, but it makes the visit more focused.
  • Comparable enquiries. Every enquiry follows the same structure, from the niche to the parts list.

Example: our built-in wardrobe configurator

The built-in wardrobe configurator is an example configurator by Modelwright with a fictional product. All sizes, rules, checks and the parts list are example values; the demo shows no prices and makes no statement on load capacity, safety or standards. The default is a niche 2.60 m wide, 2.50 m high and 650 mm deep with no slope and a 50 mm filler on each side. The configurator divides the remaining 2.50 m into three equal sections, each with two hinged doors in oak veneer and a grip groove.

Switch to a bar handle and both fillers turn red: under the example rule, the door next to the wall needs its thickness, the handle and 10 mm of air, so a 65 mm filler. In the model the door stops where the handle meets the wall, and a red marker shows the spot. One click on the suggestion widens the fillers and the check turns green.

The doors open one after another, sliding doors glide, and a drawer and a shoe pull-out slide out. The view switches between 3/4, front and side, with optional dimension labels. At the end there is a review with the checks and an example parts list, an enquiry text to copy and a PDF. The demo does not send the enquiry, the text and PDF are created in the browser only; in a project the enquiry goes to your sales team or workshop by email or webhook.

Tested: an independent QA round went through the full journey on seven emulated screen sizes from 360 px to desktop and passed 51 of 51 steps on each; after the last change the run was repeated on four of those sizes, again 51 of 51. No real phones were tested.

Example configurator · fictional product

Built-in wardrobe configurator

Plan a made-to-measure wardrobe for a niche: enter the size and any sloped ceiling, choose sections, doors and fronts, and see at once whether fillers, doors and fittings fit.

Furniture in the buyer’s room · Dimensions and sizes · Layout and planning · Options, modules and accessories

How the division, the sloped ceiling and the fit check work in detail is covered in Niche, sloped ceiling and fit checks.

How is it built for your range?

For your product we build the configurator with your carcass sizes and board thicknesses, your fronts, veneers and colours, your hardware, handles and fittings, your rules for section widths, fillers, slopes and doors, your parts list, your enquiry route and, if you wish, your prices. The model is built from your dimensions and drawings, not from a stock model. If you also make freestanding systems, Shelving configurator for manufacturers shows the same logic for shelving.

Which details retail, your own shop and contract projects need is covered in Enquiries, retail, dealers and contract projects; the effort in Furniture configurator cost. The project process is described on 3D configurator development.

Send us your construction rules and your front range, and we will reply with a proposal and a fixed-price quote.

Frequently asked questions

Does the configurator replace measuring on site?

No. It makes sure the enquiry arrives with plausible sizes and a buildable plan. The demo explicitly asks buyers to measure in several places and enter the smallest value. Your site survey is what makes it binding.

Can we use our own section widths and filler sizes?

Yes. In the demo, sections are 300 to 1,000 mm wide under an example rule, and the filler needed depends on the handle. In a project your carcass widths, your hardware table and your filler sizes replace those values.

Can it show prices?

The demo shows none. Pricing by area, section, front and fittings can be added in a project if you want buyers to see prices.

Sources

  1. Demo features: "Live in this demo" list on the built-in wardrobe configurator library page, read 15 November 2026: modelwright.de/en/library/built-in-wardrobe-configurator/
  2. Rules and default set-up: demo source code (data.js, app.js) and schema notes; test results: QA log of 15 November 2026, independent round, emulated devices.

Read next