Industries & use cases

Wheel wash configurator for manufacturers: features, benefits, implementation

What a 3D configurator for wheel wash makers must do: system type, vehicle, wash length, nozzles, water circuit, checks and an enquiry with a plan.

Short answer: a 3D configurator is worth building for wheel wash makers when it plans the system from the site: which vehicles pass through, how long the wash zone must be, how wide the lane, which nozzles and which water circuit belong to it, mobile or permanent? The result is an enquiry with a view, a plan and the check results, which your sales team or rental fleet can use to prepare a quote.

Wheel-wash system configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

Who is this for?

This guide is for managing directors, sales managers and product managers at makers of wheel-wash systems, wheel and chassis wash units and site water treatment, and at rental fleets and dealers with mobile units [1]. Typical sites are construction-site exits, quarries, gravel and sand pits, landfills, recycling yards and earthworks [1]. In our assessment, buyers are contractors, operators of extraction and waste sites, and their site management.

What is different about wheel washes?

  • The vehicle sets the system. A four-axle tipper, an articulated tipper and an articulated site dumper differ in width, tyre size and axle spacing.
  • Length depends on the tyre. Our example checks how often a tyre turns in the wash zone, which depends on wash length and tyre diameter. What value is enough is for the maker to set.
  • The unit is a system. Wash zone, nozzles, splash screens, settlement tank, pump and control kiosk must fit together.
  • Mobile or permanent is a project question. Whether the unit sits on the surface with ramps or flush in a foundation depends on how long and where it is used.

A data sheet with three lengths does not say which length suits the buyer's dumper. A model that drives the vehicle through and checks tyre revolutions against your guidelines makes that question tangible.

How are wheel washes sold, and where does the configurator fit?

Wheel washes are sold and, as mobile units, also offered through rental fleets and dealers [1]. In our assessment, the first enquiry may come from site management needing a solution for an exit. A configurator can prepare that enquiry: vehicle, type, length, lane width and water circuit chosen, checks done. Your sales team or rental fleet can then check which unit fits and whether it is available without asking for the basics first; for a rental fleet, an enquiry with vehicle, length and lane width can be matched against stock directly. How such enquiries reach the right desk is covered in enquiries from machinery and loading equipment configurators.

Which capabilities matter?

CapabilityWhyIn our example configurator
System type and installationDrive-through bath, roller system or spray platform; mobile or permanentYes
Design vehicleSize the system for the vehicleYes: 4-axle tipper, articulated tipper, articulated site dumper
Wash zone length, clear lane widthDimensions of the siteYes, with dimension lines on the model
Checks with suggestionRoom per side, tyre revolutionsYes, one-click suggestion
Nozzles, splash screens, water circuitOffer the complete systemYes: nozzle rows, screens, settlement tank, sludge conveyor, pump house, control kiosk
Drive-through animationShow the functionYes, in time-lapse
Example water and throughput calculationEstimate operationYes, as example values
Enquiry with review and PDFPrepare the quoteYes: enquiry text and a PDF with view and plan
Rental period, availability, your pricesRental fleet and salesNo, built in a project

Everything in the right-hand column is on the "Live in this demo" list [1].

What does a maker gain?

We do not promise figures. The gains are in questions and explanations:

  • The vehicle is in the enquiry. Length and width can be checked against the actual vehicle.
  • Short systems show up early. The tyre-revolution check shows when a longer wash zone makes sense.
  • The water circuit becomes visible. Settlement tank, sludge conveyor and pump house are no longer a footnote.
  • The function is explained. The drive-through shows what a brochure photo cannot.

Where are the limits?

All sizes, water quantities, throughputs and checks in the demo are example values, with no statement on cleaning result, environmental requirements, structure or standards [1]. Whether a system is permitted or adequate at a site is for the maker and the operator to settle. The configurator implements the maker's rules and does not replace planning on site.

Try the example

Our wheel-wash system configurator is an example configurator with a fictional product and example values, built by Modelwright. An example truck drives from gravel through the unit onto asphalt; its wheels turn, the nozzles spray and the tyres go from muddy to clean. On the roller system the axles stand on the rollers. There are also checks with suggestions, an example calculation of water per pass, fresh water, time per vehicle, throughput and tyre revolutions, four camera views and an enquiry with a PDF [1]. Device tests were emulated, not run on real phones.

Example configurator · fictional product

Wheel-wash system configurator

Plan a wheel-wash system for a construction site, quarry or landfill: choose the type, length and nozzles and watch an example truck drive through as its wheels come clean.

Industrial cells & machines · Dimensions and sizes · Colours · Options, modules and accessories

The wash-length, tyre-revolution and lane-width rules are explained in wheel wash length and tyre revolution rules.

How would it be built for your systems?

For your product we build the configurator with your product lines, lengths, nozzle layouts, tanks and rules, so buyers put together the right system themselves and send a complete enquiry [1]. Add your design vehicles, your values for the example calculation, your enquiry route and, if you want them, your prices or rental terms. The project process is on 3D configurator development, the cost factors in what a 3D configurator costs, and other uses in manufacturing in 3D configurators for manufacturers.

Frequently asked questions

Are the water figures in the demo real?

No. They are example values for a fictional product. In your configurator we calculate with your values, or you decide not to show a calculation.

Can the configurator take rental enquiries?

In a project, yes, with start date, duration and site as fields. The demo has a free field for site and notes but no rental fields.

Does it replace advice on site?

No. It delivers an enquiry with vehicle, dimensions and check results. Ground, water supply, disposal and permits are settled with the operator.

Sources

  1. Modelwright library: wheel-wash system configurator, product description, uses and "Live in this demo" list, read 14 November 2026: modelwright.de/en/library/wheel-wash-configurator/

Read next