Technology

Wheel wash length, tyre revolutions and lane width as configurator rules

How a wheel wash configurator checks wash length by tyre revolutions, calculates room per side and shows water and throughput as an example.

Short answer: a wheel wash configurator needs two checks and an example calculation. Tyre revolutions tell you whether the wash zone is long enough for the vehicle's tyres: length divided by tyre circumference. Room per side tells you whether the vehicle fits the lane: clear width minus vehicle width, halved. The example calculation shows water, time and throughput. Our example configurator calculates all of this live with example values for a fictional product.

Wheel-wash system configurator – preview of the example configurator
Example configurator · fictional product · example values. Loads only when you click. Open the demo page →

Which parameters does a wheel wash have?

The example configurator leads through seven steps: system, vehicle and size, nozzles and screens, water and plant, finish, review and enquiry. The main inputs:

ParameterValues in the exampleAffects
System typeDrive-through bath (6 to 16 m), roller system (4 to 8 m), spray platform with drive-over grid (6 to 24 m)Length range, nozzles, revolution check
InstallationMobile with ramps or permanent, flush in a foundationModel, ramps
Design vehicle4-axle tipper, articulated tipper, articulated site dumperWidth, tyre size, axles, length
Wash zone lengthWithin the type's rangeRevolutions, time, water
Clear lane width3.00 to 4.50 mRoom per side
NozzlesSide and underbody nozzle rowsWater quantity, message
WaterSettlement tank with or without sludge conveyor, pump houseModel and review; the tank volume in the example calculation follows from the nozzle flow

All values are example values, with no statement on cleaning result, environmental requirements, structure or standards [1].

How is the wash length checked?

The demo uses tyre revolutions in the wash zone as an example criterion for length; it is not a statement on cleaning results. For drive-through baths and spray platforms, the number of revolutions is pure geometry:

  • Tyre revolutions = wash zone length ÷ (2 × π × tyre radius)

In the example, 1.5 revolutions is an example guideline; between 1.0 and 1.5 the check is amber, below 1.0 red. A worked case with the demo's example values: the four-axle tipper has a tyre radius of 0.53 m in the example, i.e. a circumference of about 3.33 m. On a 6 m spray platform each tyre turns 6 ÷ 3.33 ≈ 1.80 times and the check is green. The articulated dumper has bigger tyres with a 0.80 m radius, about 5.03 m in circumference. In a 6 m bath that is only 1.19 revolutions, amber. The configurator suggests 8 m; one click applies the length and the check turns green.

The roller system follows different logic: the vehicle stops, and each axle group stands for a while on driven rollers. The check then states this dwell time per axle group as an example value instead of revolutions from length.

How is the lane width checked?

There must be room on each side between tyre and wheel guide. The rule in the example:

  • Room per side = (clear lane width − vehicle width) ÷ 2
  • 200 mm or more: green; 75 to 200 mm: tight; under 75 mm: does not fit.

The dumper is 2.95 m wide in the example. In a 3.00 m lane that leaves 25 mm per side, which does not fit. The suggestion takes the next width on a 250 mm step that leaves 200 mm per side: 3.50 m. All limits are example rules; the clearances your systems need are yours to set.

What does the example calculation show?

The demo shows water per pass, fresh water, time per vehicle, throughput and tyre revolutions [1]. The logic behind it, with example values:

  • Time per vehicle from wash zone and vehicle length at an example speed; on the roller system plus the dwell time per axle group.
  • Water per pass from the flow of all nozzle rows (and, for the bath, circulation) multiplied by time.
  • Fresh water as a share of the circulated water plus what the vehicle carries away.
  • Throughput as vehicles per hour with a gap between vehicles.

The calculation is labelled as example values. In a project it can use your values, or you can decide to show only the checks and leave the calculation to your sales team.

Which other rules are there?

  • Underbody nozzle rows exist on the roller system and spray platform. Choosing none there brings a message that only the tyre sidewalls are sprayed.
  • The number of side nozzle rows is limited per system type.
  • Half-height or full-height splash screens, settlement tank with or without sludge conveyor and skip, pump house, control kiosk with signal light, steel or concrete ramps and RAL colours complete the system [1].

A red or amber check does not block the enquiry; its result appears in review, enquiry text and PDF. For rental fleets a further rule is conceivable: offer per type only the lengths available as rental units. That is not in the demo and would need a maintained list of your rental stock.

What comes out at the end

The review shows every input, check and the example calculation. The enquiry text has the same rows, and the PDF a view and the plan [1]. A free field takes site and notes. In the demo, text and PDF are created in the browser; routing to a maker is not built in.

What data you supply

For your configurator we need: system types with length ranges and steps, your design vehicles with width, tyre size and axle spacing, your guidelines for revolutions and clearances, nozzle layouts, tank sizes, accessories and, if wanted, the values for a water and throughput calculation. How CAD data is prepared for the web is described in CAD to web 3D configurator.

Try it

Example configurator · fictional product

Wheel-wash system configurator

Plan a wheel-wash system for a construction site, quarry or landfill: choose the type, length and nozzles and watch an example truck drive through as its wheels come clean.

Industrial cells & machines · Dimensions and sizes · Colours · Options, modules and accessories

Test the checks in the wheel-wash system configurator, an example configurator with a fictional product and example values. Who benefits is covered in wheel wash configurator for manufacturers. The project is described on 3D configurator development.

Frequently asked questions

Is 1.5 revolutions a general guideline?

No. It is an example guideline in this demo. In your configurator your value applies.

Can it check several vehicles?

The demo uses one design vehicle. A check for several vehicles, such as the widest one and the one with the largest tyres, can be built in a project.

Does the configurator say anything about permits?

No. Permits and environmental requirements are settled by maker and operator for each site.

Sources

  1. Modelwright library: wheel-wash system configurator, product description and "Live in this demo" list, read 14 November 2026: modelwright.de/en/library/wheel-wash-configurator/

Read next